Quality is life, service is the tenet
材料電壓擊穿強度測試儀術語和定義：
材料電壓擊穿強度測試儀概述
電壓擊穿試驗儀采用計算機控制，通過人機對話方式，完成對絕緣介質材料的工頻電壓擊穿，工頻耐壓試驗。
適用于對固體絕緣材料(如：絕緣漆、樹脂和膠、浸漬纖維制品、層壓制品、云母及其制品、塑料、薄膜復合制品、陶瓷和玻璃等)在工頻電壓下擊穿電壓，擊穿強度和耐電壓的測試。
儀器對實驗過程中的各種數據快速、準確地進行采集、處理、存取、顯示、打印。
滿足標準：
GB1408-2006 GB/T1695-2005 GB/T3333 HG/T3330 /GB12656 /ASTM D149 .
GB1408-2006 絕緣材料電氣強度試驗
GB/T1695-2005 硫化橡膠工頻電壓擊穿強度和耐電壓強度試驗
GB/T3333 電纜紙工頻電壓擊穿試驗
HG/T 3330絕緣漆漆膜擊穿強度測定
GB12656 電容器紙工頻電壓擊穿試驗
ASTM D149 固體電絕緣材料在工業電源頻率下的介電擊穿電壓和介電強度試驗
安全保護功能：
◆ 試驗在試驗箱中進行，試驗箱門打開時電源加不到高壓變壓器輸入端，即高壓側無電壓。100KV測試設備高壓電極距離試驗箱壁的zui近距離大于370mm，50KV測試設備高壓電極距離試驗箱壁的zui近距離大于250mm，試驗時即使人接觸箱壁也不會有危險。
◆ 設備要安裝單獨的保護地線。接保護地線，主要是減少試樣擊穿時對周圍產生的較強的電磁干擾。也可避免控制計算機失控。
◆ 該試驗設備的電路設有多項保護措施，主要有：過流保護、失壓保護、漏電保護、短路保護、直流試驗放電報警等。
◆直流試驗放電報警功能:在設備做完直流試驗時,當開啟試驗門時設備會自動報警,直至使用設備上的放電裝置放電后報警會自動取消.(注：因為直流試驗后不放電會危險到人身安全,不能直接拿取電極,起到提醒使用人員放電以免造成人身傷害)。
◆ 試驗放電裝置，隨主機為一體化，改進了以往單獨配備一根放電桿的功能。
軟件功能:
01、軟件平臺：WINDOWS窗口操作平臺，界面直觀，便于操作
02、曲線顯示：在實驗過程中可以動態顯示試驗曲線
03、數據導出：可以對試驗結果導入EXCEL表格
04、實驗報告：可以人為設置報告名稱，并對實驗報告進行打印
05、試驗方式：可以根據需求對直流試驗和交流試驗進行靈活選擇
06、試驗方法：可以根據需求自行選擇擊穿電壓、耐壓試驗、梯度試驗
07、參數設置：可以根據不同的試驗方式及試驗方法靈活設置所需的不同參數值
08、試樣設置：可對不同標準的試樣參數靈活設置
09、人員管理：設置用戶名及密碼，不同的操作員登入進行不同的試驗，互不影響
10、標準選擇：含有不同標準，可根據需求自行選擇
11、連續操作：連續操作試驗時，可直接在軟件里選擇電機復位，進行二次試驗
技術指標：
01、輸入電壓： 交流 220 V
02、輸出電壓： 交流 0--100 KV ;
直流 0—100 KV
03、電器容量： 10KVA
04、高壓分級： 0-100KV
05、升壓速率：0.01-5.0kv
（備注：滿足標準要求并可以根據用戶需求設定不同的升壓速率）
06、試驗方式：
直流試驗：1、勻速升壓 2、梯度升壓 3、耐壓試驗
交流試驗：1、勻速升壓 2、梯度升壓 3、耐壓試驗
07、試驗介質：空氣，試驗油
08、安裝靈敏度較高的過電流保護裝置保證試樣擊穿時在0.05S內切斷電源。
09、儀器配備*故障報警系統 避免用戶操作故障儀器發生危險。（上位機報警和下位機報警）
整機組成：
1、升壓部件：由調壓器和高壓變壓器組成0～50KV的升壓部分。
2、動部件：由步進電機均勻調節調壓器使加給高壓變壓器的電壓變化。
3、檢測部件：由集成電路組成的測量電路。通過信號線把檢測的模擬信號和開關信號傳給計算機。
4、計算機軟件：通過智能電路把由檢測設備采集的測控信號傳給計算機。計算機根據采集的信息控制設備運行并處理試驗結果。
5、試驗電極：根據國家標準(1408.1-2006)隨設備提供三個電極，具體規格為：Ф25mm×25mm兩個；Ф75mm×25mm一個。
標簽：
電壓擊穿試驗儀，
介電擊穿強度試驗儀，
耐電壓擊穿測試儀，
工頻電壓擊穿測試儀，
電壓擊穿儀，
工頻介電擊穿強度測定儀，
工頻耐電壓擊穿試驗機，
電壓擊穿試驗機，
絕緣材料電氣強度測試儀，
擊穿強度試驗儀，
電氣強度測試儀，
介電強度試驗機，
擊穿電壓試驗機，
電氣介電強度試驗儀，
固體絕緣材料電氣強度試驗儀，
硫化橡膠工頻擊穿電壓強度耐電壓擊穿測定儀，
耐電壓擊穿強度試驗儀，
工頻耐擊穿電壓試驗儀，
固體電絕緣材料工業電源頻率下的介電擊穿電壓和介電強度的試驗儀，
橡膠塑料薄膜工頻電壓或直流電壓下擊穿強度和耐電壓的測試儀器。
注意事項：
●本儀器試驗過程中如空氣相對濕度大于70%，兩電極間空氣放電的距離會增加很多，所以試驗中請與儀器保持1.2米的距離。
●本儀器之控制計算機專為電壓擊穿試驗機設計，請勿隨意添加和刪除程序或移作它用。
●本公司保留對設備改進的權利，并不另行通知用戶。
注意事項：
1、介電擊穿強度試驗儀安裝時應具有獨立的接地線。
2、在開機前，操作者要首先熟悉操作方法。
3、儀器不能在有強烈腐蝕性氣體及有顆粒雜質的氣體環境中使用。
4、試驗環境溫度15度到25度之間，相對濕度60％到70％之間
5、試樣擊穿瞬間有火花產生并伴有聲響，屬正常現象。
6、每次更換試樣或接觸高壓電極時必須用高壓放電棒對高壓電極進行放電，放電時間5秒以上。
7、每次進行試驗前，必須檢查儀器接地。
注： 其它未盡事宜請，我們將竭誠為您服務。
配置
01 試驗主機 一臺
02 高壓發生器 一套
03 試驗電極 二套 (國標1408.1)
04 試驗油箱 一只
05 放電系統 一套
06 控制系統 一套
07 數據采集系統 一套
08 試驗軟件 一套 光盤
09 計算機 一套 品牌 可選 PC/EPC
10 噴墨打印機 一臺 品牌
11 產品使用說明書 一份
12 計量證書 一份
13 產品合格證 一份
14 電子穩壓器 一臺
15 藍牙發射器 一支
16 藍牙接收器 一支
Voltage breakdown tester overview
Computer controlled by voltage breakdown testing instrument, through the man-machine dialogue mode, the completion of the power frequency voltage breakdown of dielectric material,power frequency withstand voltage test.
Suitable for solid insulation materials (such as: insulating paint, resin and rubber, impregnatedfiber products, laminated products, mica and its products, plastic, thin film composite products,such as ceramic and glass) in the breakdown voltage of power frequency voltage, breakdown strength and voltage withstand test.
Instruments of various kinds of data in experiment process fast, accuray acquisition,processing, display, printing, access.
Voltage breakdown tester to meet the standard:
GB1408-2006 GB/T1695-2005 GB/T3333 HG/T3330 /GB12656 /ASTM D149.
GB1408-2006 insulation electrical strength test of material
GB/T1695-2005 vulcanized rubber power frequency voltage breakdown strength and voltage resistance strength test
GB/T3333 cable paper power frequency voltage breakdown test
HG/T 3330 insulation paint film breakdown strength determination
GB12656 capacitor paper power frequency voltage breakdown test
ASTM D149 of solid electrical insulating materials at commercial power frequencies the dielectricbreakdown voltage and dielectric strength test
Voltage breakdown testing instrument equipment safety protection function:
The experiment was conducted in the experimental box, test box door is open source applied tohigh voltage transformer input end, no voltage is high pressure side. 100KV test equipment of high voltage electrode distance test box wall nearest distance is greater than 370mm, 50KV testequipment of high voltage electrode distance test box wall nearest distance is greater than 250mm, the test even when people contact the wall of the box will not be in danger.
The equipment to install a separate protective ground. Grounding protection ground, mainly is the strong electromagnetic interference to reduce the sample breakdown when the surrounding the. Also avoid control computer control.
The test circuit of the device is provided with a number of protective measures, mainly include:over current protection, voltage loss protection, leakage protection, short-circuit protection, DC test discharge alarm.
The DC discharge alarm function: in the equipment finished the DC test, when opening the doorwhen the test equipment will automatically alarm, discharge device discharge until useequipment after the alarm will be cancelled automatically. (Note: because the DC test and not put electricity danger to personal safety, can not directly get electrode, to remind the use of personnel in order to avoid personal injury) Adult discharge.
The experimental discharge device, with the host for the integration, improves the past with separate one puts pole function.
The software function:
01, the software platform: WINDOWS windows operating platform, intuitive interface, easy operation
02, curve display: during the experiment can dynamically display the test curve
03, data export: can the test results into EXCEL table
04, experimental report: can be artificially set the report name, and print the test report
05, test mode: can flexibly select for DC test and AC test according to the requirements of
06, test methods: you can choose the breakdown voltage, voltage withstand test, gradient testaccording to the requirements of
07, the parameter settings: you can test different ways according to different parameters and test methods flexibly set the required value
08, sample set: on the specimen parameters of different standard flexible settings
09, personnel management: set the username and password, different operators in differenttest, mutual influence
Selection criteria: 10, with different standards, can choose according to need
11, continuous operation: continuous operation test, can directly select the motor reset in software, carries on two times of test
Voltage breakdown tester technical indicators:
01, the input voltage: AC 220 V
02, the output voltage: AC 0--100 KV;
DC 0 - 100 KV
03, electrical capacity: 10KVA
04, high grade: 0-100KV
05, the rate of pressure rise: 0.01-5.0kv
(Note: to meet the standard requirement and can set different rates according to the user demand boost)
06, test methods:
DC test: 1, 2, 3 speed boost pressure gradient, pressure test
AC test: 1, 2, 3 speed boost pressure gradient, pressure test
07, the test medium: air, test oil
Over current protection device 08, the installation of high sensitivity to ensure the power supply is cut off in the 0.05S sample breakdown.
09, the instrument is equipped with advanced fault alarm system to avoid user fault instrument of danger. (the host computer and slave computer alarm alarm)
Voltage breakdown tester machine component:
1, the step-up component: a pressure regulator and high voltage transformer is composed of 0 ~ 50KV pressor part.
2, dynamic components: by stepping motor even regulator is adjusted make added to the voltage change of the high voltage transformer.
The 3 part: measurement, detection circuit is composed of integrated circuit. The detection of the analog signal and switch signal to the computer through the signal line.
4, computer software: the control signal by the detection equipment acquisition to the computerthrough the inligent circuit. According to the information collected by computer controlequipment operation and processing test results.
5, the test electrode: according to the national standard (1408.1-2006) provided with the equipment of three electrodes, specifications: diameter of 25mm * 25MM two; with 75mm * 25MMa.
Tags: voltage breakdown tester, tester dielectric breakdown strength, high voltage breakdown tester, power frequency voltage breakdown tester, voltage breakdown tester, tester of electricpower frequency dielectric breakdown strength, power frequency withstand voltage breakdownvoltage breakdown testing machine, testing machine, electrical insulation material strengthtester, breakdown strength tester, electric strength tester, dielectric strength testing machine,testing machine of electric breakdown voltage, dielectric strength tester, tester electrical strengthof solid insulating materials, vulcanized rubber power frequency voltage breakdown strengthwithstanding voltage breakdown test
地址：北京市海淀區上地科技園上地十街1號
電話： 010-66024083
郵箱：3440125819@qq.com
銷售部
電話咨詢
